Vehicle Equipment

Wide body design maximizes mounting space Push-button locking storage compartment keeps valuables safe and includes one rectangular cutout and one 12V outlet cutout Simple and fast, no-drill install as the console is specific to vehicle using existing mounting points saving you time and money Computer and devices can be easily mounted to the 3-hole pattern on either driver or passenger side Includes three 12 volt plug knock-outs, three USB power ports, and two mic mount locations *Fit may vary if OEM console option is present *OEM relocation is located on the passenger side of the console box

Aluminum construction for strength and durability Cradle can be docked in both laptop and tablet orientation Key lockable for added theft deterrence Optional tablet theft deterrence module for additional safety Ergonomic design for safety and single hand operation VESA 75 mounting pattern Minimal footprint for increased usable cabin space SKU's available with power supply units

No-drill solution that attaches to the vehicle without the need to order a separate top plate. Leg kit is provided with the console box Two 12 volt plug inserts located on passenger side USB/MP3/SD card from factory console can be relocated on passenger side using knock-outs or USB/MP3/SD card/12 Volt from factory console can be relocated using faceplate, item no. 15250 Front plate of console (underneath the dash) allows a fuse block or Lind shut down timer using pre-configured mounted holes Computer can be center mounted in two locations: off-set towards the passenger on the “smiley face pattern" or on the 3-bolt pattern closer to the driver for easy articulation access Heavy gauge steel, fully welded construction for long-term durability Black powder coat finish for maximum corrosion resistance Box will ship fully assembled 3 faceplates and 3 filler panels are included Console box works with manual 4x4 shift lever Must order as is. There are no substitutions for accessories. Accessories may need to be assembled

Low profile vehicle specific console box Six (6) fasteners for mounting to transmission hump A removable top and center plate for easy radio installation and wire routing 12 Volt plug insert located on passenger side Factory USB and audio jack must be relocated using item no. 16648 & 15082 or 16648 & 15083 if you want to use them Four (4) 12 Volt knockouts located on passenger side Heavy gauge steel, fully welded constructed for long-term durability Black powder coat finish for maximum corrosion resistance Three (3) faceplates and 3 filler panels are included Console box ships fully assembled (except for accessories)

Low profile, no-drill vehicle specific console box Accommodates shifter A traction control/OEM plate (needed only if vehicle has a traction control module) Easily mounts right to transmission hump, does not require a Leg Kit or MCS Top Plate A removable center brace for easy radio installation and wire routing Ships with dash filler panels that gives the box a sleek appearance that blends in with the car’s aesthetics Threaded PEM's provided for rear mounted armrest to the console 1, 12 Volt and 2 switch knock-outs (located on shifter faceplate) Heavy gauge steel, fully welded construction for long-term durability Black powdercoat finish for maximum corrosion resistance Will ship fully assembled Includes 3 faceplates and 3 filler panels Horizontal section: Section accommodates 13" of mounting space without cup holder and is designed to house radio control heads and accessories With traction control faceplate = 7.5" of mounting internal height With traction control faceplate = 10" of mounting space With traction control faceplate and Internal cup holder = 5.5” of mounting space Designed to house full sized devices and accessories Vertical, angled sections: Angled section accommodates 5” of mounting space and is designed to house radio control heads and accessories

Low profile vehicle-specific console box Console attaches to transmission hump and does not require drilling Five (5) fasteners for mounting right to transmission hump, does not require a Leg Kit or MCS Top Plate A removable top plate and center plate for easy radio installation and wire routing Ships with molded dash filler panels that gives the box a sleek appearance that blends in with the car’s aesthetics Five (4) 12 Volt knock-outs (4 on the back and 1 on driver side) USB and MP3 knock-outs from stock console, relocated on passenger side Computer can be mounted on top of the console box and has the ability to be off-set towards the passenger on the “smiley face pattern” or mounted to the driver side with the 3-bolt hole pattern Heavy gauge steel, fully welded construction for long-term durability Black powdercoat finish for maximum corrosion resistance Includes 3 faceplates and 3 filler panels Only the console box ships fully assembled (molded dash panels must be installed on-site) Must order as is. There are no substitutions for accessories. Accessories may need to be assembled.

Low profile vehicle specific console box Five fasteners for mounting right to the transmission hump, does not require a Leg Kit or MCS Top Plate. A removable top and center plate for easy radio installation and wire routing Five 12 Volt knock-outs located on the passenger side USB and MP3 knock-outs from stock console relocated on passenger side Computer can be mounted on top of the console box and has the ability to be off-set towards the passenger on the “smiley face pattern” or mounted to the driver side with the 3-bolt hole pattern Box ships fully assembled with molded dash filler panels to give the box a sleek look for blending in with the car’s aesthetics Heavy gauge steel, fully welded construction for long-term durability Black powdercoat finish for maximum corrosion resistance Includes 3 faceplates and 3 filler panels Must order as is. There are no substitutions for accessories. Accessories may need to be assembled.

Narrowed width creates extra clearance for seat belts and gun holsters Simple and fast no-drill installation Sloped front increases visibiltiy of radios and controls Knockouts for 12V outlets and accessories are included on the top, passenger side, and back side of the console 3-hole patterns on the top of the console allows for easy installation of motion attachments

Docking station design accommodates tablet’s rotating hand strap (sold separately) Easy to use one-handed operation: Insert bottom of computer into the docking station, push top of computer against latch button until latch engages To remove, push up on latch-button with thumb to disengage and pull computer out of the docking station Access to all tablet control buttons and ports while tablet is docked Optional keyed lock for theft deterrance Upward-facing I/O ports; integrated cable strain relief and cable management system Vesa 75mm mounting pattern Rounded edges to enhance personal safety

Vehicle specific design for a custom fit Shortened length provides extra clearance for weapon retrieval Installs easily with no drilling required Rear armrest flips up when not in use to maximize workspace The Mongoose®-9" Locking Slide Arm with Short Clevis has 45 degree forward tilt capabilities and 360 degree swivel capabilities for easy viewing of laptops and devices Featuring a removable top plate for easy installation of radios and wire routing Includes knockouts for one 12V, one USB, and OEM relocations Dual cup/pen holder is removable for easy cleaning

Designed to MIL-STD 810G test procedures and complies with FCC Class A standards Small footprint - designed to maximize available space inside of vehicle Gamber-Johnson has worked with Panasonic to perform the appropriate tests needed to qualify a product as Toughbook Certified Rear-facing l/O ports, integrated cable strain relief system, and convenient cable management system Spring-loaded docking connector to ensure connectivity in the roughest terrain Front safety bracket and rear corners ensure proper alignment and docking connectivity Spring-loaded plate protects RF connector from damage when computer is not in the docking station. Plate draws back into the docking station when the computer is docked. This docking station accommodates the optional modular expansion area on the Toughbook 54/55 computer Special access area for smart card reader makes it easy to insert and eject card Push button latch with keyed lock for theft deterrence: Push the latch to release the docking connector Insert computer and push latch closed to dock computer Can be used with Motion Attachments with the VESA 75mm hole pattern only Rugged composite/steel construction with black powder coat finish for long-term durability Antenna switch position: Switch set toward outside of dock: Uses exterior antenna Switch set to inside of the dock: Uses laptop antenna

Compatible with Getac V110 convertible computer Getac electronics Docking station can be used in tablet or laptop position Rugged aluminum construction with black powder coat finish for long-term durability Front-facing l/O ports, integrated cable strain relief system POGO pin style docking connector for easy docking activation Front safety bracket helps align computer for proper docking connectivity Built-in stylus holder Push button latch with keyed lock for theft deterrence: Push the latch to release the docking connector Insert computer and push latch closed to dock computer VESA 75 mounting pattern External power supply: Lind Auto Adapter ( Item No. 7300-0463 ) is included Screen support is included with the dock

Vehicle specific design for a custom fit Dual cup/pen holder is removable for easy cleaning Installs easily with no drilling required Featuring a removable top plate for easy installation of radios and wire routing Rear armrest flips up when not in use to maximize workspace Includes knockouts for one 12V, one USB, and OEM relocations Includes the Mongoose®-9" Locking Slide Arm with Short Clevis has 45 degree forward tilt capabilities and 360 degree swivel capabilities for easy viewing of laptops and devices

Lowered top plate maintains accessibility to optional rear HVAC controls (Ford 17A ordering option) Sloped front for ease of use and visibility of radio and siren controls Easy installation, no OEM parts to be removed Console sits low between the front seats to create a more comfortable workspace Mounting holes on top plate allow for easy installation of desired motion attachments Relocation faceplate for OEM 12V, USB, AUX 12V, and switch knockout included Cup holders are removable for easy cleaning Convenient flip-up armrest and printer mount all in one Paper and printer not included Two separate pivot points on TS5 allow for swiveling, sliding, swiveling again and tilting computer to ideal location Included rear wire cover will meet up directly to Ford 85R if present

Leg kit mounts to existing center seat bolts located along transmission hump Console box filler wings going under dash are included with console Top plate on console allows for mounting a motion attachment or close-to-dash Top plate and spreader bar in middle are removable to easy installing of console and running wiring Two (2) mounting holes on console top plate made for motion attachments (driver side and passenger side) Console is low profile between the seats to create a comfortable work environment Ships fully assembled (except for console accessories i.e. faceplate, 12V outlets, etc.) Three (3) faceplate and three (3) fillers are included per console Threaded PEMS on side and rear accommodate various armrests