Gamber-Johnson

Allows for closer mounting to the dash when off-set adjustability is not needed Less stress on the vehicle mounting equipment as gravity is centered on the on pole Wrench is needed for loosening, tightening and height adjustments Heavy gauge steel construction for long-term durability Black powdercoat finish for maximum corrosion resistance

Allows for closer mounting to the dash when off-set adjustability is not needed Less stress on the vehicle mounting equipment as gravity is centered on the on pole Wrench is needed for loosening, tightening and height adjustments Heavy gauge steel construction for long-term durability Black powdercoat finish for maximum corrosion resistance

Attaches to the seat studs on the passenger side floor, under the seat Install in minutes with no drilling required Will not interfere with levers or factory installed consoles An Offset Universal Mounting Step ( DS-STEP ) maybe ordered separately to move the pole away from passenger leg space

The entire arm can rotate around 360° with locking points at every 15° To rotate the arm simply pull the front lever out, rotate to desired position and then release the lever Locking slide arm can telescope 9” to 13” from the center of the pole and utilizes the industry first, Slam and Lock technology, that allows you to simply push the computer back to the retracted position and it automatically locks into place Compatible Motion Attachment hole patterns: VESA 75mm Gamber-Johnson 2x4 NEC AMPS Tilt capabilities: 90° forward allows for tablets to be easily mounted 26° aft movement Riveted design allows for smoother tilt movement Swivel capabilities: 360° Heavy duty, spring loaded steel, side pin was tested to 50,000+ cycles Can be mounted directly to a flat surface or on any Upper Pole, Complete Pole, Center Pole, Low Profile Bracket or Gamber-Johnson 3-hole pattern Two PEMs added to the back of the Mongoose to attach the Tablet Display Mount ( 7160-0494 or 7160-0529 ) Heavy gauge steel construction for long-term durability Black powdercoat finish for maximum corrosion resistance

Angled step moves pole away from passenger leg space and attaches to the Lower Pole without any protruding edges One Offset Universal Mounting Step ( DS-STEP ) is already included with this vehicle base. However, additional Off set Universal Mounting Steps can be ordered to stack on top of each other if needed. Multiple mounting slots allow for flexible positioning of the Offset Universal Mounting Step Larger base footprint and reinforced flanges provide added stability Heavy gauge steel construction for long-term durability Black powder coat finish for maximum corrosion resistance

Will not interfere with levers or factory installed console Heavy gauge steel construction for long-term durability Black powdercoat finish for maximum corrosion resistance A Support Brace ( 7160-0230 ) is highly recommended

Bracket mounted to pole gusset allows for additional attachment to seat frame Base works with most existing work boxes Attaches to the passenger side inner front and back seat studs Does not interfere with the passenger leg space Does not require drilling Heavy gauge steel construction for long-term durability Black powdercoat finish for maximum corrosion resistance

Won't interfere with passenger leg space Can be used with factory installed console One Offset Universal Mounting Step ( DS-STEP ) is already included with this vehicle base. However, additional Offset Universal Mounting Steps can be ordered to stack on top of each other if needed For extra stability, a Support Brace ( 7160-0230 ) is recommended Heavy gauge steel construction for long-term durability Black powdercoat finish for maximum corrosion resistance Note: Forward seat travel is affected

MCS Vehicle Leg Kit is not compatible with legacy Ford F-250 trucks Legs attach to both short and long MCS Top Plates ( 7160-0085 or 7160-0086 ) Heavy gauge steel construction for long-term durability Black powdercoat finish for maximum corrosion resistance

Installs in minutes with no drilling required Attaches to the passenger side floor, under the seat Won’t interfere with levers or factory-installed consoles located on transmission hump Won’t interfere with passenger leg space Includes one (1) Offset Universal Mounting Step (Item No. DS-STEP). Additional Offset Universal Mounting Steps can be ordered to stack on top of each other if needed. For extra stability a Support Brace ( 7160-0230 ) is recommended

Low profile, no-drill vehicle-specific console box 5 fasteners for mounting right to transmission hump, does not require a Leg Kit or MCS Top Plate Vertical, angled section accommodates 7.5” of mounting space and is designed to house full-sized radios Horizontal, low profile section accommodates 13” of mounting space and is designed to house radio control heads and accessories A removable top plate and center plate for easy radio installation and wire routing Ships with molded dash filler panels that gives the box a sleek appearance that blends in with the car’s aesthetics Five 12 Volt knock-outs (4 on the back and 1 on driver's side) USB and MP3 knock-outs from stock console, relocated on passenger side Computer can be mounted on top of the console box and has the ability to be centered or off-set towards the passenger on the “smiley face pattern” Heavy gauge steel, fully welded construction for long-term durability Black powdercoat finish for maximum corrosion resistance Will ship fully assembled (molded dash panels must be installed on-site) 3 faceplates and 3 filler panels are included Console box is not compatible with legacy Dodge Chargers

Base designed to work with both the police and street model Dodge Charger Attaches to the seat studs on passenger side floor, under the seat Can be used with factory installed console A Support Brace ( 7160-0230 ) is highly recommended Heavy gauge steel construction for long-term durability Black powdercoat finish for maximum corrosion resistance

Ideal for holding pens, keys and other miscellaneous items Drain holes located in the bottom of the pocket Heavy gauge steel construction for long-term durability Black powdercoat finish for maximum corrosion resistance

Angled step moves pole away from passenger leg space Will not interfere with levers or factory installed consoles Heavy gauge steel construction for long-term durability Black powdercoat finish for maximum corrosion resistance One Off set Universal Mounting Step ( DS-STEP ) is already included with this vehicle base. However, additional Off set Universal Mounting Steps can be ordered to stack on top of each other if needed. A Support Brace ( 7160-0230 ) is highly recommended

Low profile, no-drill vehicle-specific console box Shorter console box allows for more room when mounting weapons on the prisoner cage 5 fasteners for mounting right to transmission hump, does not require a Leg Kit or MCS Top Plate A removable top plate and center plate for easy radio installation and wire routing Ships with molded dash filler panels that gives the box a sleek appearance that blends in with the car’s aesthetics Five 12 Volt knock-outs (4 on the back and 1 on driver side) USB and MP3 knock-outs from stock console, relocated on passenger side Computer can be mounted on top of the console box and has the ability to be centered or off-set towards the passenger on the “smiley face pattern” Will ship fully assembled (molded dash panels must be installed on-site) 3 faceplates and 3 filler panels are included Console box is not compatible with legacy Dodge Chargers Heavy gauge steel, fully welded construction for long-term durability Black powdercoat finish for maximum corrosion resistance

Locking lid with barrel key lock Ideal for weapons, keys and other miscellaneous items Heavy gauge steel construction for long-term durability Black powdercoat finish for maximum corrosion resistance

Locking lid with barrel key lock Ideal for weapons, keys and other miscellaneous items Heavy gauge steel construction for long-term durability Black powdercoat finish for maximum corrosion resistance

No-drill, easy to install solution Legs attach to both short and long MCS Top Plates ( 7160-0085 or 7160-0086 ) Can be used with any Gamber-Johnson Console Box (except the Ford Sedan and Utility Vehicle Specific Consoles) Heavy gauge steel construction for long-term durability Black powdercoat finish for maximum corrosion resistance

Heavy gauge steel construction for long-term durability Black powdercoat finish for maximum corrosion resistance Legs attach to both short and long MCS Top Plates ( 7160-0085 or 7160-0086 ). Legs are compatible with both the Retail and the Special Service (SSV) Models.

Armrest flips up when not is use, saving space in the mobile workstation Mounts directly to the back of the console box The printer mount lid latches shut and can be used with a paddle lock for added security Paper deflector prevents paper from curling up and jamming Cable strain relief protects connector interface on the printer engine from damage Indicator lights and on/off button are easy to see and accessible when the cover is closed